cpuz_readme_cn
5墨值下载
CPU-Z 自读文件
------------------
Version 1.76
版本号 1.76
January 2016
2016 年 04 月
Contact : cpuz@cpuid.com
联系我们 ：cpuz@cpuid.com
Web page: http://www.cpuid.com/cpuz.php
网站：http://www.cpuid.com/cpuz.php
Validation page : http://valid.x86.fr/
确认页面 ：http://valid.x86.fr/
Hall of Fame : http://valid.x86.fr/records.php
名人堂 :http://valid.x86.fr/records.php
CPUID SDK : http://www.cpuid-pro.com/devkits.php
CPUID SDK 介绍 ：http://www.cpuid-pro.com/products-services.php
Configuration file (cpuz.ini)
配置文件 (cpuz.ini)
------------------------------
The configuration file must be named cpuz.ini and be present at the same
directory level
as cpuz.exe. It contains the following :
配置文件必须存放在 cpuz.exe. 同一文件夹下名字为 cpuz.ini
[CPU-Z]
VERSION=x.x.x.x
TextFontName=
TextFontSize=14
TextFontColor=000080
LabelFontName=
LabelFontSize=14
ACPI=1
PCI=1
MaxPCIBus=256
DMI=1
Sensor=1
SMBus=1
Display=1
UseDisplayAPI=1
BusClock=1
Chipset=1
SPD=1
XOC=0
CheckUpdates=1
- TextFontName : Font used for the information boxes. 信息框字体样式
- TextFontSize : Size of the font used for the information boxes. 信息框字体大小
- TextFontColor : Color of the font used for the information boxes. Value is
expressed in hexadecimal, and consists in a classic Red/Green/Blue color code :
RRGGBB 信息框使用字体颜色。RBG 颜色：RRGGBB/000060
- LabelFontName : Font used for the label boxes. 标签框字体样式
- LabelFontSize : Size of the font used for the label boxes. 标签框字体大小
- Sensor : Set to OFF (or 0) disables sensor chip detection and voltages
measurement. 1 to enable.传感器检测设置，1 为开启、0 为关闭 关闭后将不显示温度及电压
- PCI : Set to OFF (or 0) disables the PCI information. This disables chipset,
SPD and, depending on the hardware, sensoring information. 1 to enable.PCI 检测设
置，1 为开启、0 为关闭 关闭后将不会显示主板、SPD 及硬件传感器信息
- MaxPCIBus : Sets the maximum PCI bus to scan. Default value is 256.
- DMI : Set to OFF (or 0) disables the DMI (Desktop Management Interface)
information. This concerns BIOS vendor and version, motherboard vendor and
revision. 1 to enable. DMI 设置，1 为开启、0 为关闭。管壁厚
- SMBus : Set to OFF (or 0) disables SMBus information : SPD, and, depending on
the hardware, sensoring information. 1 to enable.
- Display : Set to OFF (or 0) disables the video card information reported in
the validator. 1 to enable.
- UseDisplayAPI : Set to 1, uses the display driver to read the display adapters
information.
- BusClock : Set to 1, uses the bus clock as primary clock source. Set to 0 to
use an alternate method.
- Chipset : set to OFF (or 0) disables the memory controller and southbridge
information. 1 to enable.
- SPD : set to 0 to disable SPD reading. 1 to enable.
- XOC : eXtreme Overclock Mode : runs CPU-Z with as little system load as
possible. Your system won't be fully validated before it is manually checked.
Requires to restart CPU-Z.
- CheckUpdates : set to 0 to disable the new version checker at startup. 1 to
enable.
Parameters
参数
----------
-txt=filename : Launch CPU-Z in ghost mode (no interface appears) and generates
the register dump file (.txt)
in the same directory as the exe file.
导出报告为 txt 文本格式
-html=filename : Same as "-txt" except it generates the html report.
导出报告为 html 超文本格式
-core=id : Displays clock speed of core #id (id can be set from 0 to Number of
cores minus one).
Keys
----
F5 : save the current tab in a bmp file
F5 ：保存当前页面为 bmp 文件
F6 : save the current tab in the clipboard
F6 ：保存当前页面在剪贴板中
F7 : save cvf file in the current directory
F7 ：保存 CVF 在默认目录
Cache Latency Tool
------------------
The cache latency tool can be downloaded at that address :
http://www.cpuid.com/medias/files/softwares/misc/latency.zip
Cache Latency Tool 下载地址 ：
http://www.cpuid.com/medias/files/softwares/misc/latency.zip
History
更新历史
-------
--------------------------------------------------------------------------------
of 12
5墨值下载
【版权声明】本文为墨天轮用户原创内容，转载时必须标注文档的来源（墨天轮），文档链接，文档作者等基本信息，否则作者和墨天轮有权追究责任。如果您发现墨天轮中有涉嫌抄袭或者侵权的内容，欢迎发送邮件至：contact@modb.pro进行举报，并提供相关证据，一经查实，墨天轮将立刻删除相关内容。
下载排行榜
评论